Fixed build issue

arduino/HalMultiSensor/HalConfiguration.h

@@ -1,18 +1,18 @@
 #ifndef HALCONFIGURATION_H
 #define HALCONFIGURATION_H
 
-#include "Definitions.h"
+#include "HalDefinitions.h"
 
 
 // POWER CONSUMPTION SENSOR
 #define POWERCON_ENABLED // comment out to disable sensor
-#define POWERCON_HARDWARE       HardwareDH1750()
+#define POWERCON_HARDWARE       HardwareBH1750()
 #define POWERCON_PROTOCOL       ProtocolOregon(118)
 #define POWER_TIMER_MULTIPLIER 1 // poling in minutes
 
 // TEMPERATURE SENSOR
 #define TEMPERATURE_ENABLED // comment out to disable sensor
-#define TEMPERATURE_HARDWARE    HW_DHT11
+#define TEMPERATURE_HARDWARE    HardwareDHT11(5)
 #define TEMPERATURE_PROTOCOL    ProtocolOregon(100)
 #define TEMPERATURE_TIMER_MULTIPLIER 1 // poling in minutes
 

arduino/HalMultiSensor/HalInterfaces.h

@@ -1,6 +1,7 @@
 #ifndef HALINTERFACES_H
 #define HALINTERFACES_H
 
+
 class Hardware
 {
 public:
@@ -11,7 +12,7 @@ class HardwarePowerConsumption : public Hardware
 {
 public:
     // returns number of pulses from power meter
-    virtual int getConsumption() = 0;
+    virtual unsigned int getConsumption() = 0;
     virtual void reset() = 0;
 };
 
@@ -26,7 +27,7 @@ class HardwareLight : public Hardware
 {
 public:
     virtual void setup() = 0;
-    virtual int getLuminosity() = 0;
+    virtual unsigned int getLuminosity() = 0;
 };
 
 
@@ -38,4 +39,23 @@ public:
     virtual void send() = 0;
 };
 
+class ProtocolPowerConsumption : public Protocol
+{
+public:
+    virtual void setConsumption(unsigned int cons) = 0;
+};
+
+class ProtocolTemperature : public Protocol
+{
+public:
+    virtual void setTemperature(float temp) = 0;
+    virtual void setHumidity(unsigned char humidity) = 0;
+};
+
+class ProtocolLight : public Protocol
+{
+public:
+    virtual void setLuminosity(int lumen) = 0;
+};
+
 #endif // HALINTERFACES_H

arduino/HalMultiSensor/HalMultiSensor.ino

@@ -2,52 +2,64 @@
 A interrupt based sensor device that reads multiple sensors and transmits
 the data to a central location.
 */
+#if (ARDUINO >= 100)
+#include <Arduino.h>
+#else
+#include <WProgram.h>
+#endif
+#include <Wire.h>
 
-InterruptUtil timerInterrupt;
+#include "HalInterfaces.h"
+#include "HalDefinitions.h"
+#include "HalConfiguration.h"
+#include "Interrupt.h"
+
+
+Interrupt* interrupt;
 
 unsigned int timerMultiplierMAX;
 unsigned int timerMultiplier = 0;
 
 // Sensors
-HardwarePowerConsumption powerSensor;
+HardwarePowerConsumption* powerSensor;
-HardwareTemperature tempSensor;
+HardwareTemperature* tempSensor;
-HardwareLight lightSensor;
+HardwareLight* lightSensor;
 
 // Protocols
-HardwarePowerConsumption powerProtocol;
+ProtocolPowerConsumption* powerProtocol;
-HardwareTemperature tempProtocol;
+ProtocolTemperature* tempProtocol;
-HardwareLight lightProtocol;
+ProtocolLight* lightProtocol;
 
 
 
-void timerInterrupt();
+void timerInterruptFunc();
 
 void setup()
 {
-    timerMultipleMAX = POWER_TIMER_MULTIPLIER * TEMPERATURE_TIMER_MULTIPLIER * LIGHT_TIMER_MULTIPLIER; // Find a lowest common denominator
+    timerMultiplierMAX = POWER_TIMER_MULTIPLIER * TEMPERATURE_TIMER_MULTIPLIER * LIGHT_TIMER_MULTIPLIER; // Find a lowest common denominator
-    pinInterrupt = InterruptUtil(timerInterrupt);
+    interrupt = new Interrupt(timerInterruptFunc);
-    pinInterrupt.setupTimerInterrupt(60*1000); // one minute scheduled interrupt
+    interrupt->setupTimerInterrupt(60*1000); // one minute scheduled interrupt
     
     // Setup Sensors and protocols
     #ifdef POWERCON_ENABLED
-    powerSensor = POWERCON_HARDWARE;
+    powerSensor = new POWERCON_HARDWARE;
-    powerSensor.setup();
+    powerSensor->setup();
-    powerProtocol = POWERCON_PROTOCOL;
+    powerProtocol = new POWERCON_PROTOCOL;
-    powerProtocol.setup();
+    powerProtocol->setup();
     #endif
 
     #ifdef TEMPERATURE_ENABLED
-    tempSensor = TEMPERATURE_HARDWARE;
+    tempSensor = new TEMPERATURE_HARDWARE;
-    tempSensor.setup();
+    tempSensor->setup();
-    tempProtocol = TEMPERATURE_PROTOCOL;
+    tempProtocol = new TEMPERATURE_PROTOCOL;
-    tempProtocol.setup();
+    tempProtocol->setup();
     #endif
 
     #ifdef LIGHT_ENABLED
-    lightSensor = LIGHT_HARDWARE;
+    lightSensor = new LIGHT_HARDWARE;
-    lightSensor.setup();
+    lightSensor->setup();
-    lightProtocol = LIGHT_PROTOCOL;
+    lightProtocol = new LIGHT_PROTOCOL;
-    lightProtocol.setup();
+    lightProtocol->setup();
     #endif
 }
 
@@ -55,7 +67,7 @@ void setup()
 void loop() {}
 
 
-void timerInterrupt()
+void timerInterruptFunc()
 {
     ++timerMultiplier;
     if (timerMultiplier > timerMultiplierMAX)
@@ -65,10 +77,10 @@ void timerInterrupt()
     #ifdef POWERCON_ENABLED
     if(timerMultiplier == POWER_TIMER_MULTIPLIER)
     {
-        unsigned int consumption = powerSensor.getConsumption();
+        unsigned int consumption = powerSensor->getConsumption();
-        powerSensor.reset();
+        powerSensor->reset();
-        powerProtocol.setConsumption(consumption);
+        powerProtocol->setConsumption(consumption);
-        powerProtocol.send();
+        powerProtocol->send();
     }
     #endif
 
@@ -76,11 +88,11 @@ void timerInterrupt()
     #ifdef TEMPERATURE_ENABLED
     if(timerMultiplier == TEMPERATURE_TIMER_MULTIPLIER)
     {
-        unsigned int temperature = tempSensor.getTemperature();
+        unsigned int temperature = tempSensor->getTemperature();
-        unsigned int humidity = tempSensor.getHumidity();
+        unsigned int humidity = tempSensor->getHumidity();
-        tempProtocol.setTemperature(temperature);
+        tempProtocol->setTemperature(temperature);
-        tempProtocol.setHumidity(humidity);
+        tempProtocol->setHumidity(humidity);
-        tempProtocol.send();
+        tempProtocol->send();
     }
     #endif
 
@@ -88,9 +100,9 @@ void timerInterrupt()
     #ifdef TEMPERATURE_ENABLED
     if(timerMultiplier == LIGHT_TIMER_MULTIPLIER)
     {
-        unsigned int lumen = lightSensor.getLuminosity();
+        unsigned int lumen = lightSensor->getLuminosity();
-        lightProtocol.setLuminosity(lumen);
+        lightProtocol->setLuminosity(lumen);
-        lightProtocol.send();
+        lightProtocol->send();
     }
     #endif
 

arduino/HalMultiSensor/HardwareBH1750.cpp

@@ -15,16 +15,13 @@ based on Christopher Laws, March, 2013 code.
 #include <util/delay.h>
 
 
-BH1750::BH1750() {}
+void HardwareBH1750::setup() {
-
-void BH1750::begin(uint8_t mode) {
   Wire.begin();
-  //write8(mode);
+  configure(BH1750_CONTINUOUS_HIGH_RES_MODE);
-  configure(mode);
 }
 
 
-void BH1750::configure(uint8_t mode) {
+void HardwareBH1750::configure(uint8_t mode) {
     switch (mode) {
         case BH1750_CONTINUOUS_HIGH_RES_MODE:
         case BH1750_CONTINUOUS_HIGH_RES_MODE_2:
@@ -45,8 +42,16 @@ void BH1750::configure(uint8_t mode) {
     }
 }
 
+unsigned int HardwareBH1750::getConsumption()
+{
+    return pulses;
+}
+void HardwareBH1750::reset()
+{
+    pulses = 0;
+}
 
-uint16_t BH1750::readLightLevel(void) {
+unsigned int HardwareBH1750::getLuminosity(void) {
   uint16_t level;
 
   Wire.beginTransmission(BH1750_I2CADDR);
@@ -81,7 +86,7 @@ uint16_t BH1750::readLightLevel(void) {
 /*********************************************************************/
 
 
-void BH1750::write8(uint8_t d) {
+void HardwareBH1750::write8(uint8_t d) {
   Wire.beginTransmission(BH1750_I2CADDR);
 #if (ARDUINO >= 100)
   Wire.write(d);

arduino/HalMultiSensor/HardwareBH1750.h

@@ -12,16 +12,12 @@ http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1750fvi-
 based on Christopher Laws, March, 2013 code.
 
 */
-
 #ifndef HARDWAREBH1750_H
 #define HARDWAREBH1750_H
 
-#if (ARDUINO >= 100)
+#include <Wire.h>
-#include <Arduino.h>
+#include "HalInterfaces.h"
-#else
+
-#include <WProgram.h>
-#endif
-#include "Wire.h"
 
 #define BH1750_DEBUG 0
 
@@ -58,14 +54,16 @@ based on Christopher Laws, March, 2013 code.
 #define BH1750_ONE_TIME_LOW_RES_MODE  0x23
 
 
-class BH1750 {
+class HardwareBH1750 : public HardwarePowerConsumption, public HardwareLight{
- public:
+public:
-  BH1750();
+    virtual void setup();
-  void begin(uint8_t mode = BH1750_CONTINUOUS_HIGH_RES_MODE);
+    virtual unsigned int getLuminosity();
-  void configure(uint8_t mode);
+    virtual unsigned int getConsumption();
-  uint16_t readLightLevel(void);
+    virtual void reset();
 
- private:
+    void configure(uint8_t mode);
+private:
+    unsigned int pulses;
     void write8(uint8_t data);
 
 };

arduino/HalMultiSensor/HardwareDHT11.cpp

@@ -15,13 +15,13 @@
 // + added references
 //
 
-#include "dht11.h"
+#include "HardwareDHT11.h"
 
 // returnvalues:
 //  0 : OK
 // -1 : checksum error
 // -2 : timeout
-int dht11::read(int pin)
+int HardwareDHT11::read()
 {
 	// BUFFER TO RECEIVE
 	uint8_t bits[5];
@@ -80,6 +80,4 @@ int dht11::read(int pin)
 	if (bits[4] != sum) return -1;
 	return 0;
 }
-//
+
-// END OF FILE
-//

arduino/HalMultiSensor/HardwareDHT11.h

@@ -12,26 +12,26 @@
 // George Hadjikyriacou - Original version
 // see dht.cpp file
 // *** Terry King: Changed include Arduino.h for 1.0x  
-// include core Wiring API and now Arduino
-#if defined(ARDUINO) && ARDUINO >= 100
-  #include "Arduino.h"
-  #else
-  #include "WProgram.h"
-  #endif
-
 #ifndef dht11_h
 #define dht11_h
 
+#include <Arduino.h>
+#include "HalInterfaces.h"
+
 #define DHT11LIB_VERSION "0.3.2"
 
-class dht11
+class HardwareDHT11 : public HardwareTemperature
 {
 public:
-    int read(int pin);
+    HardwareDHT11(int pin);
-	int humidity;
+    virtual void setup(){};
-	int temperature;
+    virtual int getTemperature();
+    virtual int getHumidity();
+    int read();
+
+private:
+    unsigned int pin;
+    float temperature;
+    unsigned char humidity;
 };
 #endif
-//
-// END OF FILE
-//

arduino/HalMultiSensor/HardwarePhotocell.cpp

@@ -1,23 +1,24 @@
+#include "HardwarePhotocell.h"
 
 
-public void pinInterrupt()
+void pinInterrupt()
 {
-    ++pulse;
+    //++pulse;
 }
 
 
-public HardwarePhotocell::setup()
+void HardwarePhotocell::setup()
 {
-    pinInterrupt = InterruptUtil(pinInterrupt);
+    interrupt = new Interrupt(pinInterrupt);
-    pinInterrupt.setupPinInterrupt(PC2); //PC3
+    interrupt->setupPinInterrupt(PC2); //PC3
 }
 
-public unsigned int HardwarePhotocell::getConsumption()
+unsigned int HardwarePhotocell::getConsumption()
 {
     return pulse;
 }
 
-public unsigned int HardwarePhotocell::reset()
+void HardwarePhotocell::reset()
 {
     pulse = 0;
 }

arduino/HalMultiSensor/HardwarePhotocell.h

@@ -1,6 +1,9 @@
 #ifndef HARDWAREPHOTOCELL_H
 #define HARDWAREPHOTOCELL_H
 
+#include "HalInterfaces.h"
+#include "Interrupt.h"
+
 
 class HardwarePhotocell : public HardwarePowerConsumption 
 {
@@ -10,7 +13,8 @@ public:
     virtual void reset();
 
 private:
+    Interrupt* interrupt;
     unsigned int pulse;
-}
+};
 
 #endif // HARDWAREPHOTOCELL_H

arduino/HalMultiSensor/Interrupt.cpp

@@ -1,8 +1,11 @@
+#include "Interrupt.h"
 #include <avr/power.h>
 #include <avr/sleep.h>
 
 
-void Interrupt::pinInterrupt()        // here the interrupt is handled after wakeup
+
+
+void pinInterrupt()        // here the interrupt is handled after wakeup
 {
   // execute code here after wake-up before returning to the loop() function
   // timers and code using timers (serial.print and more...) will not work here.
@@ -10,7 +13,12 @@ void Interrupt::pinInterrupt()        // here the interrupt is handled after wak
   // just want the thing to wake up
 }
 
-void Interrupt::setupInterrupt()
+void Interrupt::setupPinInterrupt(int pin)
+{
+
+}
+
+void Interrupt::setupTimerInterrupt(unsigned int milliseconds)
 {
     /*
      * The 5 different modes are:

arduino/HalMultiSensor/Interrupt.h

@@ -1,6 +1,9 @@
 #ifndef INTERRUPT_H
 #define INTERRUPT_H
 
+#include <Arduino.h>
+
+
 typedef void (*InterruptFunction) ();
 
 class Interrupt
@@ -10,9 +13,10 @@ public:
 
     //static void sleep(int milliseconds);
     void setupPinInterrupt(int pin);
-    void setupTimerInterrupt(int milliseconds);
+    void setupTimerInterrupt(unsigned int milliseconds);
 private:
     InterruptFunction callback;
-}
+
+};
 
 #endif // INTERRUPT_H

arduino/HalMultiSensor/ProtocolNexa.h

@@ -1,4 +1,8 @@
 #ifndef PROTOCOLNEXA_H
 #define PROTOCOLNEXA_H
 
+#include "HalInterfaces.h"
+
+
+
 #endif // PROTOCOLNEXA_H

arduino/HalMultiSensor/ProtocolOregon.cpp

@@ -1,8 +1,8 @@
-#include <Wire.h>
+#include "ProtocolOregon.h"
 
-#define RF_TX_PIN = 10;
+#define RF_TX_PIN 10
-#define RF_DELAY = 512;
+#define RF_DELAY 512
-#define RF_DELAY_LONG RF_DELAY*2;
+#define RF_DELAY_LONG RF_DELAY*2
 #define RF_SEND_HIGH() digitalWrite(RF_TX_PIN, HIGH)
 #define RF_SEND_LOW() digitalWrite(RF_TX_PIN, LOW)
 
@@ -13,18 +13,18 @@ void ProtocolOregon::setup()
   RF_SEND_LOW();
 }
 
-virtual void ProtocolOregon::setTemperature(float temp)
+void ProtocolOregon::setTemperature(float temp)
 {
-    this.temperature = temp;
+    this->temperature = temp;
 }
-virtual void ProtocolOregon::setHumidity(unsigned char humidity)
+void ProtocolOregon::setHumidity(unsigned char humidity)
 {
-    this.humidity = humidity;
+    this->humidity = humidity;
 }
-virtual void ProtocolOregon::setConsumption(unsigned int cons)
+void ProtocolOregon::setConsumption(unsigned int cons)
 {
-    this.temperature = cons;
+    this->temperature = cons;
-    this.humidity = 0;
+    this->humidity = 0;
 }
 
 void ProtocolOregon::send()

arduino/HalMultiSensor/ProtocolOregon.h

@@ -1,11 +1,14 @@
 #ifndef PROTOCOLOREGON_H
 #define PROTOCOLOREGON_H
 
+#include <Arduino.h>
+#include "HalInterfaces.h"
 
-class ProtocolOregon : public ProtocolTemperature : public ProtocolPower
+
+class ProtocolOregon : public ProtocolTemperature, public ProtocolPowerConsumption
 {
 public:
-    ProtocolOregon(unsigned char address) : address(address){}
+    ProtocolOregon(unsigned char address) : address(address){};
 
     virtual void setup();
     virtual void setTemperature(float temp);
@@ -14,7 +17,7 @@ public:
     virtual void send();
 private:
     unsigned char address;
-    unsigned float temperature;
+    float temperature;
     unsigned char humidity;
 };